MATLAB FIXED-POINT TOOLBOX - RELEASE NOTES User's Guide Page 24
- Page / 99
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
24 www.xilinx.com System Generator for DSP Getting Started Guide
UG639 (v 12.2) July 23, 2010
Chapter 2: Installation
Note: If installation instructions for your particular platform are not provided here, please refer to the
installation instuctions that come with your Platform Kit. For instructions on how to install a Xilinx USB
Cable and cable driver software on a Windows or Linux Operating System, refer to the Xilinx
document titled: USB Cable Installation Guide
JTAG-Based Hardware Co-Simulation
Installing an ML402 Board for JTAG Hardware Co-Simulation
Installing an ML605 Board for JTAG Hardware Co-Simulation
Installing an SP601/SP605 Board for JTAG Hardware Co-Simulation
Third-Party Hardware Co-Simulation
As part of the Xilinx XtremeDSP™ Initiative, Xilinx works with distributors and many
OEMs to provide a variety of DSP prototyping and development platforms. Please refer to
the following Xilinx web site page for more information on available platforms:
http://www.xilinx.com/products/boards_kits/index.htm
Compiling Xilinx HDL Libraries
If you intend to simulate System Generator designs using ModelSim, you must compile
your IP (cores) libraries. This topic describes the procedure.
ModelSim SE
The Xilinx tool that compiles libraries for use in ModelSim SE is named compxlib. The
following command can, for example, be used to compile all the VHDL and Verilog
libraries with ModelSim SE:
compxlib –s mti_se –f all –l all
Complete instructions for running compxlib can be found in the ISE Software Manual
titled “Command Line Tool User Guide”.
- Generator for 1
- Table of Contents 3
- Chapter 4: Getting Started 4
- About This Guide 7
- Additional Resources 8
- Conventions 8
- Online Document 9
- Preface: About This Guide 10
- Introduction 11
- The Xilinx DSP Block Set 12
- FIR Filter Generation 13
- Support for MATLAB 14
- System Resource Estimation 15
- Hardware Co-Simulation 16
- System Integration Platform 17
- Chapter 1: Introduction 18
- Installation 19
- Chapter 2: Installation 20
- Table 2-3: 20
- Table 2-4: 20
- UNC Paths Not Supported 21
- Software Prerequisites 21
- Post Installation Tasks 22
- UG639 (v 12.2) July 23, 2010 23
- ModelSim SE 24
- Setting the Size 25
- Setting the Number of Entries 25
- Release Information 27
- Hardware Recommendations 28
- Known Issues 29
- Release Notes 12.1 30
- Xilinx Blockset Enhancements 31
- Release Notes 11.4 35
- Table 3-5: 37
- Table 3-6: 37
- Release Notes 11.3 39
- Existing Block Updates 40
- Table 3-7: 41
- Table 3-8: 41
- Getting Started 43
- ® Simulator 44
- The Xilinx DSP Blockset 45
- Defining the FPGA Boundary 46
- Creating the DSP Design 48
- Generating the HDL Code 49
- Chapter 4: Getting Started 50
- DSP blockset 50
- Lesson 1 Summary 52
- Lab Exercise: Using Simulink 52
- Fixed-Point Numeric Precision 53
- Overflow and Round Modes 55
- Bit-Level Operations 56
- The Reinterpret Block 57
- The Convert Block 58
- The Concat Block 59
- Slice Block 60
- The BitBasher Block 61
- Lesson 2 Summary 62
- Lab Exercise: Signal Routing 62
- Lesson 3 - System Control 63
- The MCode Block 64
- State Machine Example 66
- The Expression Block 67
- Reset and Enable Ports 68
- Bursty Data 69
- Lesson 3 Summary 70
- Lab Exercise: System Control 70
- Lesson 4 - Multi-Rate Systems 71
- Up and Down Sampling Blocks 72
- Debugging Tools 75
- Sample Period “Rules” 76
- Lesson 5 - Using Memories 78
- Initializing RAMs and ROMs 79
- System Generator RAM Blocks 80
- System Generator ROM Blocks 81
- The Delay Block 82
- The FIFO Block 83
- Shared Memory Block 84
- Lab Exercise: Using Memories 85
- Lesson 6 - Designing Filters 86
- The Virtex DSP48 Math Slice 87
- FIR Compiler Block 88
- Using FDA Tool Coefficients 90
- Virtex®-5 architecture 91
- Black Box Examples 92
- ChipScope Examples 92
- DSP Examples 93
- M-Code Examples 94
- Processor Examples 94
- Shared Memory Examples 95
- Timing Analysis Examples 96
- Miscellaneous Examples 96
- System Generator Demos 97
Related products and manuals for Software manuals MATLAB FIXED-POINT TOOLBOX - RELEASE NOTES
(716 pages)
(43 pages)© 2020, manymanuals.com. All rights reserved. | 1.797 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals